Ye Olde Rocket Forum

Go Back   Ye Olde Rocket Forum > Work Bench > Building Techniques
User Name
Password
Auctions Register FAQ Members List Calendar Today's Posts Search Mark Forums Read


Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-01-2010, 08:29 AM
GregGleason's Avatar
GregGleason GregGleason is offline
U.S. Manned Space Program Buff
 
Join Date: Mar 2009
Location: Houston
Posts: 1,298
Default Wood Filler Question - Small Holes

I need a recommended wood filler for the following situation:

I have a nose cone plug that was made of poplar (kiln dried). It was machined about six months ago and now there are little pin holes in the wood. It looks like there were some creatures in there that wanted to bore their way out. The holes (about half a dozen or so) are very tiny (about 0.5 to 1.0 mm), but they do affect the surface. I know it was an "inside job" because the wood has been in saran wrap almost the entire time.

Since I am going to use it as a plug for a mold, I need to seal and wax it. Before I can do those tasks, I need to fill these holes and sand then to shape.

Can someone suggest a product that is suited for the task?

Greg

Last edited by GregGleason : 06-01-2010 at 08:57 AM.
Reply With Quote
  #2  
Old 06-01-2010, 08:51 AM
ghrocketman's Avatar
ghrocketman ghrocketman is offline
President, MAYHEM AGITATORS, Inc.
 
Join Date: Jul 2005
Location: Nunya Bizznuss, Michigan
Posts: 13,443
Default

I would use a product called "Plastic Wood".
It is actual cellulose (powdered wood) fibers dissolved in an organic solvent.
Lots of folks on here will probably reccommend the water based "Elmers fill n' finish" which is far INFERIOR to plastic wood as an actual filler material.
Plastic Wood is actually HARD when it dries, whereas the elmers product is actually very soft.
__________________
When in doubt, WHACK the GAS and DITCH the brake !!!

Yes, there is such a thing as NORMAL
, if you have to ask what is "NORMAL" , you probably aren't !

Failure may not be an OPTION, but it is ALWAYS a POSSIBILITY.
ALL systems are GO for MAYHEM, CHAOS, and HAVOC !
Reply With Quote
  #3  
Old 06-01-2010, 10:28 PM
Mark II's Avatar
Mark II Mark II is offline
Forest Sprite
 
Join Date: Dec 2006
Location: Back Up in the Woods
Posts: 3,657
Default

I like to use water-thinned Elmer's Wood Filler (a k a Fill 'N Finish) to fill spirals and other patch jobs on tubes, but I don't care for using it on wood, especially nose cones. So I basically agree with gh. Minwax also makes a product that looks similar to Plastic Wood, but I haven't tried it. Elmer's makes other wood filler products that are packaged in squeeze tubes. These do not seem to be the same thing as FNF. (I cannot imagine what it would take to squeeze FNF out of a plastic tube. The stuff in the tub has the consistency of a damp block of chalk.) Elmer's makes a variety of wood fillers; some are very tough after they cure. That may be more than what you need, though. A rock-hard filler may not be necessary for an object that will subsequently be coated with polyurethane or Polycrylic and then used as a mold master.

MK
__________________
Mark S. Kulka NAR #86134 L1,_ASTRE #471_Adirondack Mountains, NY
Opinions Unfettered by Logic • Advice Unsullied by Erudition • Rocketry Without Pity
+09281962-TAK-08272007+
SAM # 0011
Reply With Quote
  #4  
Old 06-02-2010, 05:01 AM
stantonjtroy's Avatar
stantonjtroy stantonjtroy is offline
Scale builder
 
Join Date: Dec 2006
Location: Maryland
Posts: 208
Default

If you're going to use it for a mold plug, why not just use Bondo? You Could even melt some wax into the holes. It only has to stand up for the mold, not paint or flight.
Reply With Quote
  #5  
Old 06-02-2010, 06:50 AM
GregGleason's Avatar
GregGleason GregGleason is offline
U.S. Manned Space Program Buff
 
Join Date: Mar 2009
Location: Houston
Posts: 1,298
Default

I took GH's advice and got "Plastic Wood". My "gut instinct" was telling me to stay away from anything water-based, since it typically makes wood swell, and not in a good way.

I'll let everyone know how it works out. I've never done this before so I'm sure I'll have more surprises ahead.



Greg
Reply With Quote
  #6  
Old 06-02-2010, 08:17 AM
rokitflite's Avatar
rokitflite rokitflite is offline
Master Modeler
 
Join Date: Mar 2005
Posts: 952
Default

Quote:
Originally Posted by GregGleason
My "gut instinct" was telling me to stay away from anything water-based, since it typically makes wood swell, and not in a good way.

Greg


You are just sooo wrong Greg...
__________________
Scott

NAR #32070
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump



All times are GMT -5. The time now is 04:49 PM.


Powered by: vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Ye Olde Rocket Shoppe © 1998-2024