#1
|
|||
|
|||
Gabriel engine retention
I've got a Gabriel rocket (an old Centuri rocket).
Never flown it because the lack of an engine hook baffles me. The instructions just say to wrap some masking tape around the engine (A8-5, B4-6, B6-6, C6-7) before inserting. Is that really going to retain the engine and pop the chute or, as I imagine, just pop the engine and result in an unslowed rocket falling from several hundred feet? |
#2
|
||||
|
||||
Back in the good old days we didn't have engine hooks. Masking tape was the way to keep them in the motor tube. And sometimes it worked so well you needed pliers to get them back out!
__________________
Lee Reep NAR 55948 Projects: Semroc Saturn 1B, Ken Foss Designs Mini Satellite Interceptor In the Paint Shop: Nothing! Too cold! Launch-Ready: Farside-X, Maxi Honest John, Super Scamp |
#3
|
|||
|
|||
Thanks! Good to know.
That was the other direction I could see it going, wedged so tight I wouldn't be able to extract. I guess finding the happy medium is the key. |
#4
|
||||
|
||||
Yes, it works... Bit of an art to it, compared to motor hooks, but not exactly rocket science LOL...
The motors tend to swell some when fired, as the casing heats up, making them tighter... So long as you can't pull the motor out with two fingers, is probly tight enough... Should be able to install it with a gentle twisting motion.... Removal is the same but usually a little tighter... The main thing is, turn the motor casing ONLY the opposite direction from the direction you wrapped the tape around it... That way the end of the wrapped tape can't "double back" on itself by sticking to the inside of the motor tube as it's being turned... Also, heat from the motors tend to soften the tape adhesive and make it stickier and gooier... Which can make it a lot harder to extract the motor when it cools down... Best to remove the the motor not long after flight, basically asap.... Later! OL JR
__________________
The X-87B Cruise Basselope-- THE Ultimate Weapon in the arsenal of Homeland Security and only $52 million per round! |
#5
|
|||
|
|||
Quote:
__________________
Paul If we weren't all crazy, we would go insane - Jimmy Buffett NAR #87246 www.wooshrocketry.org |
#6
|
||||
|
||||
When pushing in a friction fit engine, be very careful not to grip the rocket body too tightly.
It's easy to crimp the body tube right above the top of the fins, especially on a minimum diameter BT-5 or BT-20 model. Fred Shector gave the best advice about engine removal. Pull a friction fit engine right after you pick it up. You can easily pull out a still warm engine. Let it cool down and you'll have to get out the pliers.
__________________
Hans "Chris" Michielssen Old/New NAR # 19086 SR www.oddlrockets.com www.modelrocketbuilding.blogspot.com http://www.nar.org/educational-reso...ing-techniques/ Your results may vary "Nose cones roll, be careful with that." Every spaceman needs a ray gun. Look out - I'm the Meister Shyster! |
#7
|
|||
|
|||
Excellent! Thanks for the additional tips. I probably wouldn't have thought to consider the direction of the tape wrap. I'm hoping to do some launches tomorrow and I'll give the Gabriel it's long overdue first launch.
|
#8
|
||||
|
||||
I've seen L motors friction fitted successfully!
__________________
I love sanding. |
#9
|
|||
|
|||
Pliers are ok in a pinch, but a dowel works much better. Get a long oak one slightly smaller than the intenal diamater of your engine, slide it up to the nozzle and then push the rocket down. This always works. This removes the twisting motion that can ruin the rocket. And yes, it is usually easier when the engine is still warm. I have crushed to many nozzles with pliers or damaged the airframe with the twist.
__________________
BAR in his second tour of duty. Nar# 32629 |
#10
|
|||
|
|||
Quote:
Good idea Basically just need to lengthen the stick I use as an impromptu recovery wadding plunger. Thx! |
Thread Tools | Search this Thread |
Display Modes | |
|
|