#1
|
||||
|
||||
A Place For My Stuff...
This thread is a "catcher's mitt" for those designs in the new catalog that are missing RKT files and JPG images. It's just a place-holder thread for these rockets, so it's not open for general posts or other designs. Thanks.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#2
|
||||
|
||||
Test Rocket C (2009)
Just a very basic 18mm rocket with a payload section.
Length: 28.00" Diameter: 1.17" (ST-11) Fin Span: 5.17" Weight: 1.42 oz A8-3......194'......Dv 4 FPS B4-4......462'......Dv 7 FPS B6-4......468'......Dv 12 FPS C6-5......990'......Dv 12 FPS All engines reach safe flight V on a 36" x 1/8" standard rod. Fin sheet included below. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#3
|
||||
|
||||
4" Rhemus
A 4" upscale of my Rhemus, created by Fore Check back on September 5, 2007.
Length: 63.75" Diameter: 4.00" (LOC 3.9") Fin Span: 19.39" Weight: 62.75 oz As designed, the model uses engine-based deployment charges instead of electronics. The simulation results below reflect this method of deployment. I284W-10.........2924'.........Dv 21 FPS.........48" guide required I300T-10.........2346'.........Dv 40 FPS.........48" guide required I354FJ-10........2829'.........Dv 32 FPS.........60" guide required I366R-10.........2814'.........Dv 29 FPS.........48" guide required Launch lugs are not shown in the plan. Use whichever method suits your preferences. Fin sheet patterns included (next post). Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#4
|
||||
|
||||
4" Rhemus Fin Sheets
Two sheets, 3/16" A/C plywood. One sheet 12" x 48". One sheet 12" x 40".
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#5
|
||||
|
||||
Loadmaster "A"
This was the first version of the Loadmaster, and which for some reason never got posted. It differs from the "B" version only in the nose cone. I used an elliptical cone for the "A".
Length: 18.81" Diameter: 0.908" (ST-8) Fin Span: 4.43" Weight: 1.15 oz A8-3.......232'......Dv 5 FPS B4-4.......506'......Dv 8 FPS C6-5......1021'......Dv 4 FPS The B6-4 is not recommended. All engines reach safe flight V on a 36" x 1/8" launch rod. The fin sheet is the same as in the "B" version. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#6
|
||||
|
||||
Lightning Bug (2005)
A two-stage design from April 6, 2005.
Length: 18.30" Diameter: 0.759" (ST-7) Fin Span: 3.26" Weight: 0.96 oz A10-0T/A3-4T......812'......Dv 26 FPS......36" x 1/8" launch rod Streamer recovery. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#7
|
||||
|
||||
Pochard (2007)
Something whipped up during the "open frame fin" heydays. I have a date of January 22, 2007 for these files.
Length: 23.59" Diameter: 0.908" (ST-8) Fin Span: 5.90" Weight: 1.21 oz A10-3T......271'......Dv 11 FPS A8-3........244'......Dv 11 FPS These are currently the only engines recommended. The A3-4T, as well as B-C engines, have very high Dv numbers. Requires a standard 36" x 1/8" rod. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#8
|
||||
|
||||
Scarab (2003)
Another from the ancient pre-historic days of BARCLONE. January 28, 2003.
A fantasy-futuristic type of model. Works well on lower-impulse engines (A & B). Higher impulse engines produce too great a Dv. Length: 15.75" Diameter: 0.976" Fin Span: 8.12" Weight: 1.17 oz A8-3........235'......Dv 7 FPS A10-3T......260'......Dv 6 FPS B4-4........525'......Dv 22 FPS All engines reach flight V on a 36" x 1/8" rod. Best performance is with the 13mm A10, and the model might be set up with either an adapter or a fixed 13mm mount. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#9
|
||||
|
||||
EVModels Interdictor Series (2006)
From April of 2006, this was a series of HPR/MPR models by EchoVictor. There are five variants included in the set, but all share the same outward appearance. The difference is in the internal arrangement of engine tubes. The number attached to each version indicates the number of and size of the engines.
The five RKT files are included together in a single ZIP file. They are also located SOMEWHERE on YORF, but I cannot seem to locate them with a general search. General specs: Length: 36.55" Diameter: 2.60" (BT-80) Fin Span: 14.60" Weight: Varies with each model Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#10
|
||||
|
||||
Spitfire 13E (2006)
Another simple 3FNC for 13mm engines. A "Schoolyard Sounder" with great Dv and altitude numbers.
Length: 13.30" Diameter: 0.908" (ST-8) Fin Span: 4.06" Weight: 0.79 oz A3-4T......~415'......~Dv 4 FPS......36" x 1/8" launch rod Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
Thread Tools | Search this Thread |
Display Modes | |
|
|